rear wheel bearing
Moderator: Octane2097
-
- CB-Uk Newbie
- Posts: 48
- Joined: Tue Jul 16, 2013 8:28 pm
rear wheel bearing
Does a rear drum on a 97 b have one roller bearing or two. I know there is a small one you temove to get drum off.
-
- CB-Uk User
- Posts: 70
- Joined: Sat Feb 16, 2013 7:38 pm
- Location: newcastle upon tyne
Re: rear wheel bearing
I got a 98 corsa b and Mine had 2 sets of bearings, like you describe one is a small set that does come off with the hub
Sent from my X10i using Tapatalk 2
Sent from my X10i using Tapatalk 2
-
- CB-Uk User
- Posts: 70
- Joined: Sat Feb 16, 2013 7:38 pm
- Location: newcastle upon tyne
Re: rear wheel bearing
Meant drum btw
Sent from my X10i using Tapatalk 2
Sent from my X10i using Tapatalk 2
-
- CB-Uk Newbie
- Posts: 48
- Joined: Tue Jul 16, 2013 8:28 pm
Re: rear wheel bearing
Take it the other one is pressed in to the drum?
- johnny
- Senior Moderator
- Posts: 4875
- Joined: Sun Jul 08, 2012 4:26 am
- Location: Donegal,Ireland
Re: rear wheel bearing
Its not pressed in, when you take the drum off it will fall out but theres two rings inside the drum tjat need hammered out and in
Make sure to take the rubber seal off the hub as most people forget about it
Make sure to take the rubber seal off the hub as most people forget about it
If it doesn't fit,
force it,
If it breaks,
It needed replacing anyway
force it,
If it breaks,
It needed replacing anyway
-
- CB-Uk Newbie
- Posts: 48
- Joined: Tue Jul 16, 2013 8:28 pm
Re: rear wheel bearing
So its just the race thats in the drum and the bearing its on the stub axle?
-
- CB-Uk Newbie
- Posts: 49
- Joined: Thu Aug 22, 2013 8:16 pm
Re: rear wheel bearing
when taking mine off. All bearings came out with drum just took rubber seal off took bearings out and replaced em put new bearings and grease bk in and job done! Really ur meant to change race when doing bearings but after carefully inspecting old ones they were fine i just put bk together. Surprising how often they do it like that in garages to save a few quid. Took me 15 mins to do nice and easy wee job! A mate got charged 75 bux for this at garage. Makes u wonder why mechanics never see the doh!
- johnny
- Senior Moderator
- Posts: 4875
- Joined: Sun Jul 08, 2012 4:26 am
- Location: Donegal,Ireland
Re: rear wheel bearing
An old bearing case may look ok but is more than likly expanded as there always harder to take out, if your cutting corners on your own car even when the case comes with the kit, do not give out about mechanics, if you go to a cowboy for cheap labour thats up to you, but f**k you if your basically saying I cut corners because im f**k qualifyedpdrpaul wrote:when taking mine off. All bearings came out with drum just took rubber seal off took bearings out and replaced em put new bearings and grease bk in and job done! Really ur meant to change race when doing bearings but after carefully inspecting old ones they were fine i just put bk together. Surprising how often they do it like that in garages to save a few quid. Took me 15 mins to do nice and easy wee job! A mate got charged 75 bux for this at garage. Makes u wonder why mechanics never see the doh!
If it doesn't fit,
force it,
If it breaks,
It needed replacing anyway
force it,
If it breaks,
It needed replacing anyway
-
- CB-Uk Newbie
- Posts: 49
- Joined: Thu Aug 22, 2013 8:16 pm
Re: rear wheel bearing
no dis respect to u intended. But i knw a few guys in garages 1 of which works at a vauxhall dealer and iv heard some of the corners he cuts as well as others in there! And makes u think how the f**k some f**k get in there!! Eg when i first got car gave it to vauxhall for simple wheel bearing adjustment. (Got it bk hme 7 mile) checked bolts on wheels to double check they were gd and the were litrally hand tight no where near 110 nm what they should be! As said no dis respect am sure ur gd at ur job. But some garages are robbing bastards.
-
- CB-Uk User
- Posts: 70
- Joined: Sat Feb 16, 2013 7:38 pm
- Location: newcastle upon tyne
Re: rear wheel bearing
Bit late but Forgot to check back but did mine myself, the larger bearing is pressed in one with its race, easily tapped out using a hammer and a large hole punch or screw driver, just use your old race as a shim when tapping your new one in, just don't tap it all the way use a screw driver and hammer to do the last bit as your old race we get stuck as well, just be careful not to slip and scratch the new race , easy job.
Sent from my X10i using Tapatalk 2
Sent from my X10i using Tapatalk 2