Lack of power at pull away
Moderator: Octane2097
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Lack of power at pull away
Hi all just got a X reg 3d corsa and seem to be having a small prob with power at pull aways say you come to a junction and all most stop and then start to accelerate out of it in first the car seems to judder with no power a work mate tells me it may be the clutch slipping and it may well be as it's been around the world at 89.000 or so and no clutch change I know of so any views on this please feel free to fire away thanks lots
-
- CB-Uk Newbie
- Posts: 49
- Joined: Thu Aug 22, 2013 8:16 pm
Re: Lack of power at pull away
could be a few things when was it last serviced?? could be dirty fuel injector or possible egr valve... any eml lights on you had codes read/ tried paper clip test.
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Re: Lack of power at pull away
The service sticker in the window tells me it had a service in June this year I did have to replace the Crank angle sensor last week after it failed on me I have a frend is bringing over a code reader and no lights on the dash I will have to see whot the code reader tells me and get back to you lol thanks lots
-
- CB-Uk Newbie
- Posts: 49
- Joined: Thu Aug 22, 2013 8:16 pm
Re: Lack of power at pull away
was your crank sensor genuine?? I got a cheap aftermarket camshaft sensor for my bertone that may as well not been there lol couldnt rev above 4 k etc cheap sensor and vauxhall dont mix lol
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Re: Lack of power at pull away
It was a bosch from euro car parts £30 it looked well made is it worth going and getting a genuine part I don't know who vauxhall get to make sensors for them
-
- CB-Uk Newbie
- Posts: 49
- Joined: Thu Aug 22, 2013 8:16 pm
Re: Lack of power at pull away
Bosch is good so wouldnt worry but I would get codes read that should point you to problem;) let us know what ya get..
- johnny
- Senior Moderator
- Posts: 4875
- Joined: Sun Jul 08, 2012 4:26 am
- Location: Donegal,Ireland
Re: Lack of power at pull away
Bosch is oem so the sensor should be good as said take it to a local garage and get the codes read
If it doesn't fit,
force it,
If it breaks,
It needed replacing anyway
force it,
If it breaks,
It needed replacing anyway
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Re: Lack of power at pull away
Yes I think that is the way to go I will let you know whot the codes come up with thanks for your help
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Re: Lack of power at pull away
Just got around to connecting the code reader and having a little look at engine management /transmission and to my shock I have no fault codes or pending codes so will have to delve a little deeper in to the problem ?
-
- CB-Uk Newbie
- Posts: 49
- Joined: Thu Aug 22, 2013 8:16 pm
Re: Lack of power at pull away
thats a pain when you dont get a answer from code reader:/ just a thought but I had a wee corsa b I got from auction with similar problem seemed to hesitate when pulling away was almost like throttle cable was sticking when pushing it down then bang you got bit to much didnt always happen tho... anyway put a bottle of forte injector cleaner through and bingo was perfect after few mile driving. I only buy forte stuff now. bout 14 quid a bottle seems to work well and is used by trade. other things may be worth trying clean your throttle body out and check your spark plugs. its such a good indication of how combustion and your engine is running.
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Re: Lack of power at pull away
Thanks for the tip I will find some and give it a go sorry for the late reply
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Re: Lack of power at pull away
Just a qwik update coming back from Nottingham yesterday and found that the rev counter has stopped working once more when I got the car the rev counter did not work and a change of the Crank angle sensor got it going so all was good some people have told me the sensor is a part that tends to fail a lot on this model I did put a good quality part ( bosch ) in it can anyone tell me if this part is prone to fail like this
- stanc3w0rks
- CB-Uk User
- Posts: 3303
- Joined: Tue Feb 18, 2014 4:08 pm
- Location: mayo, ireland
Re: Lack of power at pull away
I would guess there is something else causing the sensor to fail if it is that sensor gone already
- ronald5256
- CB-Uk User
- Posts: 57
- Joined: Tue Aug 12, 2014 1:26 pm
Re: Lack of power at pull away
I think I will have to pull the sensor and test it and work back from it to get to the root of it maybe put my code reader back on it and see if I have any pending codes poping up now
- johnny
- Senior Moderator
- Posts: 4875
- Joined: Sun Jul 08, 2012 4:26 am
- Location: Donegal,Ireland
Re: Lack of power at pull away
Exactly what stance said but at the same time with the sensor being so cheap it's worth buying a second, even if it doesn't sort it you have a spare
If it doesn't fit,
force it,
If it breaks,
It needed replacing anyway
force it,
If it breaks,
It needed replacing anyway