B204 into Corsa B

[stanc3w0rks]

Has anyone got any info on this swap? I know I need to customise an engine and probably gearbox mount. The wiring is going to be hard. Any way to bypass the imobiliser without reflashing the Ecu? Would the saab gearbox work with the Corsa? I dont think it would as I think the saab gearbox does not use a cable.

Sent from my GT-I8200N using Tapatalk

[johnny]

You'd need to get on mig if it's still going and talk to one of the vauxhall guru's from back in the day

I know you need mounts but they can be bought off the shelf from eBay or lmf, the chassis needs a wallop cut out of it and the immobiliser just needs the chip from the key from the donor

[stanc3w0rks]

So for the immobiliser, would I just tape the saab key to the saab ecu and use corsa key and barrell??

Sent from my GT-I8200N using Tapatalk

[johnny]

Yeah or put the chip into the corsa key so it's immobilised when it's parked on the drive

[stanc3w0rks]

Yeah or put the chip into the corsa key so it's immobilised when it's parked on the drive

Good thinking joined mig to ask a few questions. Finding a f20 box in the west of Ireland is going to be the hardest part I think lol.

Sent from my GT-I8200N using Tapatalk

[coupe77]

You need cut out a bit of the drivers side of the chassis
Get the ecu remapped to get the immobiliser or get the early one they don't have them fitted then make up an o/s engine mount
Then it's just patching in the loom or go to Saab uk there is a guy that makes up the looms so it's nearly plug and play


Sent from my iPhone using Tapatalk

[stanc3w0rks]

Thanks for that info. Trying to get in contact with Nige for the loom adapter. Does the ecu need flashing for immobiliser or will the way Johnny said work?

Sent from my GT-I8200N using Tapatalk

[stanc3w0rks]

Also is type 1 and 2 corsa B just pre/post 97?

Sent from my GT-I8200N using Tapatalk

[coupe77]

The later ones need a remap
The early ones don't
It's the Saab ecu I am on about
You can patch the engine loom in its just the wires don't match up with Vauxhall


Sent from my iPhone using Tapatalk

[coupe77]

Just don't use a 1.0 as you will need to change the dash loom


Sent from my iPhone using Tapatalk

[stanc3w0rks]

Yeah its a 1.2 16v.. The wiring is going to be the hardest part for me.. hopefully buying the Saab tomorrow.its a 00 Saab 9-3.

Sent from my GT-I8200N using Tapatalk

[stanc3w0rks]

Anyone know how much of the Saab loom I need to keep?

Sent from my GT-I8200N using Tapatalk

[coupe77]

You will need the full engine loom with the ecu plugs


Sent from my iPhone using Tapatalk

[stanc3w0rks]

You will need the full engine loom with the ecu plugs


Sent from my iPhone using Tapatalk

Thanks. Wasn't sure if I needed any of the loom that runs up behind the dash. So basically I just need the part of the loom running from the ECU to engine and disconnect the part going in behind dash?



Sent from my GT-I8200N using Tapatalk

[coupe77]

http://www.corsasport.co.uk/board/viewt ... tid=660882

Have you got the f23 box and shafts
There are 2 Ecus 1 has 2 plugs if you got that one you will need the plug from the dash loom if it's not you just do like the xe conversion


Sent from my iPhone using Tapatalk