Silver corsa b envoy 12v

[johnny]

Think I personally prefer Mhws aswell bud thanks for nice comments mades it worth while I guess

So my multi meter arrived today not used one since my college days haha



So went and checked ecu plug

It's getting a live to this red wire and a switched live to this black wire





So does this mean it's probably an earth problem?


Sent from my iPhone using Tapatalk

Only seen this now, black should be switched live affik anyway, black was switched in the corsa sports anyway

Sent from my SM-G900F

[Cmcorsa]

Think I personally prefer Mhws aswell bud thanks for nice comments mades it worth while I guess

So my multi meter arrived today not used one since my college days haha



So went and checked ecu plug

It's getting a live to this red wire and a switched live to this black wire





So does this mean it's probably an earth problem?


Sent from my iPhone using Tapatalk

Only seen this now, black should be switched live affik anyway, black was switched in the corsa sports anyway

Sent from my SM-G900F

Live is black on vectra according to the guide? Plug gets a live feed just to double check ignition live and why coil pack ain't getting a feed

Not much to update guys been too busy with my new job nearly forgot about the corsa haha till Sunday which was sunny

Bought a machine polisher and wet and dry sand paper and couple more rollers so that's the next step once I'm back off night shift

Also painted slabs silver and refitted the mhw and phase 2 bumpers after I painted those





Prefer it a lot more tbh



Also collected these gaz adjustable mini rear struts for maximum lows front will need brung down a touch more and 195/45/15 all round for the stance I'm after



Then once outside is done I will work my way from back to front exhaust needs completing big brake conversion needs discs and then get it fitted refurb front coilovers and redo wiring

[Cmcorsa]

Had an early finish today so got stuck into the corsa for a wee while since we have cracking weather

Exhaust system is all aligned going weld it all up soon race tub is on also


Rear mini shocks and my "custom" springs



Now sits really low and need to run 195/45/15



Freshened up the front wheel arches and coilovers







Also removed helper springs sits like this now





Will look better with 195/45/15 tyres all round though underside is pretty much done now


Sent from my iPhone using Tapatalk

[Cmcorsa]

well another failure at trying get it running I've am at a lost end don't have any daily transport atm d over s work van and can't fun around in that when I'm off so going strip the engine out the corsa and start all over! Doing something that ain't been done before is proving its difficulties

Had a quick browse online managed to find a 2.0 16v ecotec no everyone's cup of tea but it's complete with ecu loom etc exhaust manifold coolant hoses drive shafts everything bar a gearbox and got it at a bargain price

So I popped to the west coast of Glasgow to pick it up 3 hour round trip later



Just need a gearbox and conversion mounts and larger hub flanges. Can pick them up new on eBay so that's handy. Least I can paint engine bay properly and and al paint the 2.0 all up so its all fresh looking


Sent from my iPhone using Tapatalk

[Cmcorsa]

Couple hours spare this morning got a birthday party later spend removing the unwanted power steering and calibra engine mounts

Quick paint and freshen up block needs a 2nd coat tbh





Few other bits I got



Painted my vectra calipers



And ordered these



More soon


Sent from my iPhone using Tapatalk

[Cmcorsa]

Discs arrived bloody huge lol





Won't get them fitted till weekend if I'm off or might wait and get braided hoses while am at it

Selection of shiny bolts ordered first lot arrived today




Sent from my iPhone using Tapatalk

[Cmcorsa]

Couple other updates

Drivers side conversion mount bought



Also bought this strengthening kit since my cross member is a little soft in areas



Also more tesa loom tape, new number plates and holders and hopefully collecting a f18gearbox this weekend

Finally got some of the new bolts fitted and colour coded the timing belt cover






Sent from my iPhone using Tapatalk

[Cmcorsa]

Went and collected a f16 gearbox this morning should make it accelerate pretty decent



More bolts arrived so got them fitted looking loads better now also fitted my new intake pipe going get a new one for after the afm and new filter while am at it




Sent from my iPhone using Tapatalk

[Cmcorsa]

Finish night shift last night had a wee sleep and decided to get stuck into the corsa today

Downpipe and arb removed tie bars unbolted



Engine mounts undone gear linkage removed coolant drained rad out hoses undone

Then engine lowered out



Gearbox painted



Luckily I had an old transducer for the gearbox



Now Ive compared the driveshafts calibra ones are thicker there slightly longer will that be ok





Also ordered arb lowering blocks and bought a ecu kit online





That's all for now


Sent from my iPhone using Tapatalk

[Cmcorsa]

Another good day outside so got stuck into the corsa again really motivated Atm

Finished removing the 1.8 and repainted the full pay except crossmember





Painted the gearbox engine block and few other bits







Then I started to swap brakes over and what a nightmare that turned out to be as can't remove passenger caliper bolts proper rounded



Slabs just fit over lol



My strenthening kit arrived so al get that welded onto crossmember and painted hopefully next weekend





Sent from my iPhone using Tapatalk

[Cmcorsa]

Weathers a bit poo atm but got an hour or so at the corsa earlier

Start charge loom removed



Looked crap so got the loom tape out



Bm came in handy for sitting it when it rained lol

Rear mount painted up done it silver to match the box



Also anyone got a plate that is missing of my box my 1.0 box doesn't have it




Sent from my iPhone using Tapatalk

[nathcarr]

All coming together lad shame to hear that the 1.8 conversion didn't go as planned but least you got something else sorted for its replacement and you didn't give up so thumbs up for that lad [emoji106] the 2.0 will be better anyway I would of thought least there's a lot of info out there if you get stuck because a lot of people have done it and parts are easy to get for the conversions so should be less of a pain to rectify any problems you may come across. Keep up the good work lad [emoji106]


Sent from my iPhone using Tapatalk

[Cmcorsa]

All coming together lad shame to hear that the 1.8 conversion didn't go as planned but least you got something else sorted for its replacement and you didn't give up so thumbs up for that lad [emoji106] the 2.0 will be better anyway I would of thought least there's a lot of info out there if you get stuck because a lot of people have done it and parts are easy to get for the conversions so should be less of a pain to rectify any problems you may come across. Keep up the good work lad [emoji106]


Sent from my iPhone using Tapatalk

Thanks bud would of been easy to give in but got myself back working now and a work van etc so no needing pay insurance or anything arm means I've plenty funds to build it right this time. Shame it's a bank holiday today been waiting on parts arriving lol the ecotec won't be everyone's choice but it's basically a Redtop anyway I've built one of them before so I know what I'm doing this time which helps

[Cmcorsa]

Had a little while spare earlier so got stuck in about the x20xev wiring

Found a couple split wires and dodgey repairs so sorted them out and started loom wrapping takes ages this but looks so much better afterwards







Next up was the corsa 9pin plug



Going to soldier these connections that's why wires are wrapped together atm

Was going to get start and charge loom fitted but weather changed and my garage is a mess atm once that's done i will make a start on the corsas wiring


Sent from my iPhone using Tapatalk

[Cmcorsa]

The joys of night shift a cant sleep well during the day so instead of lying in bed bored I decided to finish off the corsa wiring

Start charge loom swapped over



Ran into an issue tho not sure where this earth cable should go now since usually it's on top starter bolt



Next up removed the loom got it loom taped up then brung into the house to solider up





Ecu set arrived



The fitment for plug was slightly different but modified it with the solider iron and now it fits also soldiered the 9 pin plug onto the loom



Just need the male side of 9 pin plug to wire into the corsa 1.0 loom as don't fancy doing a dash loom swap


Sent from my iPhone using Tapatalk