Corsa-B.uk - Vauxhall, Opel and Holden Corsa B Owners Club

theres a M reg cav in my local scrappy 2.0 16 valve hasnt been touched only come in last week as part of the scrapage scheme. only done 91k aswell

carl...i would get the engine anyways for you! Keep it and get the gaskets and that redone over the next year or so, and build up a conversion kit. Then by the time you can afford to insure one, you will have a conversion ready to go!

i am gonna get the block bored to 87mm and get some new 87mm XE pistons. is about £250 for the pistons, rings and gudgeon clips, so thats all fine and dandy.

Am still annoyed over it though. Such a ballache!

i would chris but i cnt afford it and i cnt rob it as it ways too much even if took it apart would still be too heavy to robb.
they are an engine specialist though acording to there website so i should imagine they have a few in there sheds the amount of cars without engines

well...more bad luck, i have lost my locking wheels nut key. Bastard! It has been a bad week with the little things this week, is pissing me off.

There is no positives to report. Engine is on hold and there is nothing else that needs sorting. I have gotta pay adam for these springs when i get paid so thats more cash gone. But they have made a difference. Defo gonna be a long month...and its going to be a few months before this block is anywhere near!

This car is once again getting to me!

UPDATE - PLANS

Right, i have got my head around what needs doing and what im going to do now, so thought i'd let you all know.

Plans for rebuild
- Rebore of cylinders to 87mm, increasing capacity to 2050cc and removing dish and lips from linings.
- Brand new AE/Mahle 87mm standard pattern XE pistons. Will raise the compression to 11.3 and kick the power up quite a bit. Will run the XE rods.
- SEH crank Polished up and restored. Doesnt need a regrind - has been checked and is fine.
- Heavy Duty, Holden main and big end bearings.
- ARP rod bolts, Vauxhall standard main cap bolts.
- New oil pump internals swapped into old pump casing (recommended as original casing is stronger and better quality).
- Custom Cometic head gasket to match 8v head to bored 16v block.
- Lightened Alternator drive pulley (single V).

So yea, just got to get the money together and it should be done in a couple of months. This one i have got is smoking badly and i am not sure the oil pressure is building right as the new lifters are very noisy. Need this done asap though and want the car running right so i can enjoy it before our lovely weather goes and i cant take it to wales.

i dnt know about any of that stuff but sounds really expensive

and i know what you mean about wales i was there the other day and was amazed at the roads it was a shame i had the misses as i had to hold back

quite cheap those bits lol.

rob - you find out at all how much their after for the 20xe please?

yea its gonna be OE stuff so is gonna keep the cost from spiralling. Its not a race engine or anything...i just need it to be strong and reliable whilst giving me some pace and the poke that i dont have atm considering its a 2 litre.

you know where i am if need any help

i sat here and read you log from start to finish and got to say i love your car m8 lol

is it sorted yet??? lol

keep it up!!

glad you like it. its nowhere near finished yet!

the engine is gonna take some saving to get done tbh, and atm im just driving it, and its fine and dandy apart from smoke, but i dont care!

i should have enough money this month to buy the pistons and hopefully next month will mean the rest comes through. Pistons are the main expense tbh.

i will be doing some maintainance this weekend though.

well, bit of an update. I am turning the project around in quite a big way. Not something people would have expected...but its for the best i think.

I wont reveal it yet, but all will be told as soon as its sorted and i have the item in my possession.

I have loads of bits for sale too...so have a look in classifieds to see if there is anything of any use to you.

I wont reveal it yet, but all will be told as soon as its sorted and i have the item in my possession.

3 litre twin charged RX7 engine maybe? lol

A turboed 1.6 16v???

mobiius wrote:

I wont reveal it yet, but all will be told as soon as its sorted and i have the item in my possession.

3 litre twin charged RX7 engine maybe? lol

i bloody wish! i havent got the welding capabilities to fabricate, else i would have a bloody go!